Thursday, September 27, 2012

Hiking in Tenn and some new lights

It's been a few days, I know, but I had to take some time off an relax a bit before autumn really sets in. I took a trip down to the Smoky Mountains and did some hiking and saw some friends. I finally got around to seeing Gabe Mountain and Hen Wallow Falls; it's one of the shorter hikes but I kept doing the longer hikes in the past as Hen Wallow is a 'there and back' rather than part of a loop. I got up real early to catch the morning light.
Gabe Mountain trail
I spend some time at the falls as I knew it would be some time before anyone else arrived and I would have the place to myself for awhile.
Hen Wallow Falls
When I got home, it was back to work on the trailer, as I had a couple days of my vacation left. I finished the headliner (as you can see in the pics below) and installed a couple of shelves along the ceiling. The lights I had ordered had also arrived; I had found on Amazon a string of LED lights that were 12v and were RGB, meaning I could change their color to anything that suited me. In addition I had picked up some 110v LED lights on clearance after the holidays last year. This gives me all the lighting I need (with one exception) for when I'm plugged in and for when I'm running on solar.

I've gotten the 110v lights installed, both a white and a blue string. I can use both or just each separately as I installed a switched outlet just for them. (blue is shown)
 The 12v LEDs will be installed along the opposite wall as indirect lighting. Here they are when I was testing them right out of the package. They came with an infrared receiver and a 42 button remote. The direct light from the string overwhelmed the camera, but as you can see from the reflected glow I had them set to violet. The remote comes with 24 preset colors, and places for 6 user defined settings, as well as flash, strobe and fade; more than I'll need (or ever use).
I think I'm ready to begin building the bed frame and look into buying a mattress.

Friday, September 14, 2012

A desk and a start on the ceiling

It's been awhile since I've had a good desk that I can work at. Right now I either work in bed or at a "desk" I made in the RV that I sit sideways at. I was actually looking at a new desk (frosted glass with a keyboard drawer at $100) that I was going to treat myself on. Well, the other day I was in the ReStore when I found a desk at a good price, actually a better desk but without a keyboard drawer. But between the price ($30) and that it would fit curve at the front of the trailer better. I wish I had taken a picture of it before I modified it, so you could get a better I idea of what I did.

First of all, it was obviously designed for computers before flat-screens, as there was a glass tier, about 2" above the main glass desk, that sat back behind the two wings and was large enough for a CRT monitor. Above that (and again behind the two side wings) was a third glass shelf, at the same level as the speaker shelves. The two wings were at an angle very similar to the curve of the front of the trailer (or so I was thinking) and would mount right up if I eliminated the back portion.

And that is what I ended up doing, there were two metal frames, bottom and middle, that I cut the back squares off, just leaving the three angled sections. I then drilled holes in them to mount what was the rear support in the center. I also moved the shelf brackets for the top shelf out onto the edges of the speaker shelves so that I can still use it. Here is the result:

 I did add one more thing after this photo, I added an additional support at the center of the upper glass shelf. I was concerned that the speaker shelves alone wouldn't support much weight upon it.

It is attached to the wall, so it is not going to slide around, with enough room for cables between it and the wall. I was planning to mount the left and right monitors to the (white) rail, but this desk will work out better as I can mount them closer to eye level without taking up desk space. The center monitor still will take desk space, as it will not mount on a wall.

As you can also see, I've finished putting up the side rails and the trim around the window (yea!). I've also added the second layer of insulation in the roof and the system to keep it in place. I started on the headliner as well, but started running out of daylight, so I'll probably finish that over the next couple of days after work.

Until then!

Thursday, September 13, 2012

Need my socks and an air guitar

I apologize for the hiatus, I had some vehicle trouble, but it's taken care of now.
I actually did get quite a bit done: The floor is done, with a few tricks. It looks great!

As well as the wall papering. I did something a little different with the walls (as you can see). You know the old adage that horizontal stripes make you look...well, bigger? I thought I'd try it to make it seem bigger. It does seem to work; I was working on the layout for the (upcoming) bed frame and I had to go back out to the trailer twice to verify the space. I kept thinking it was bigger! So, what did I use to achieve this? Bed sheets. They were about 1/10th the price of wallpaper; it was a little more than paint (after figuring in adhesive) but a much better result in my opinion. I have put most of the side rails back up (repainted them as well), a couple more to go as I have to cut them to fit around the windows.

While doing the floor, I didn't want to lose the use of the tie-downs, as I will be hauling the motorcycle when I'm traveling, so I came up with this:
Now you don't see it...
now you do!








All four tie-downs can be accessed this way, and when covered up they are barely noticeable. I'm currently figuring a way for a "tail-gate" for the floor, to keep debris out when I close the trailer's tail-gate; probably some small hinges and some of the extra floorboards.

More tomorrow!