Showing posts with label Microhouse. Show all posts
Showing posts with label Microhouse. Show all posts

Saturday, January 25, 2014

Grandma's awesome tiny home.

    This grandmother is awesome; by herself, she turned her backyard shed into a tiny home.
    When Monica Smith's daughter lost her home (the source article does not say why) she decided the give her 2 bedroom house to her daughter and five grandkids, moving into the storage shed in the back yard. By herself (and some help of her grandchildren) she built a full kitchen, a living area, a dining area, and upstairs is the bedroom in just an 8' by 10' space. It all looks amazing! I've seen apartments that weren't furnished as well.
    More pictures follow:







A lovely kitchen:

The cozy dining area:

A couch and the TV:



And a spacious bedroom upstairs:



Here's the view from the door, to tie it all together:


Monica has made a wonderful answer to a difficult situation, she also gets to stay near her family. If more people do this, maybe this is what will become the norm, instead of thinking outside the box.

Wednesday, October 2, 2013

Applying the graphics

After several delays, rain, cold weather, and a back injury (not me fortunately) we finally got the graphics applied.

Tuesday, September 3, 2013

Vinyl graphics, part 1


Yesterday evening I got together with a friend of mine that owns a vinyl cutter and we finally started cutting the graphics for the trailer. In my previous post you saw him weeding, or removing the unwanted vinyl, on the large viking graphic for the left side. Here's the finished piece all ready for the backing.
Next we started on the large raven banner for the front of the trailer. Here I will show the steps how a vinyl graphic is made (for those that are unfamiliar).
A roll of vinyl in loaded into the machine which connects to a computer very much like a printer or a plotter. The software sends the vector designs to the cutter which begins cutting. After the machine cuts the vinyl you have a sheet with barely visible cuts on it. Beginning at the outside, we begin weeding and you can begin to see the design.

 
And here's the finished banner reading for the backing. The backing covers the design and is used for transferring the vinyl from the paper to it's destination. On the right are a couple of smaller pieces with the backer on them.
 

And those smaller pieces in place. I picked up a kindle, cheap, and it reminded me of the hitchhiker guide, so it needed "Don't Panic!" in large friendly letters on it. The other was for the kayak, which I have named the "Wetware" (it's a computer term). There is more that will be going on the kayak later.
 

It will probably be a couple days before we can get the rest cut and put on the trailer.

Graphics for the trailer!

Started working of the graphics for the trailer last night. More tonight!

Wednesday, July 24, 2013

A late update

    My apologies, a link to mirror posts from another location has not been working. I only recently found out, but to be honest, there have not been a lot of them. I will be spending the next few days re-posting them here.
    Firstly, to catch you up with events:
    I did finish the trailer and have been living in it since last September. I moved the RV out of the spot and backed the new trailer in. Using four pavers and jack stands, I lifted and leveled the trailer, making it very stable.
    I'm pleased to report that the insulation did fine and I stayed warm all winter. I use an oil-filled radiator (the one you will remember from an earlier post) and it did just fine. With the insulation in the trailer I did not have to turn the heat up past two on most days, three on the coldest (the highest setting on it is 6), so I count that as a win.
    I put together an outdoor kitchen; I was fortunate enough to find a used solid-state refrigerator at the ReStore for $35. If you are not familiar with them I shall explain: Solid-state (or Peltier) refrigerators do not have a compressor and refrigerant, they use a silicon chip that, when powered, transfers heat from one side of the chip, to the other. Two heat sinks with fans, one on either side of the chip, complete the entire workings. The heat sink on the inside absorbs heat from the air inside the refrigerator, the chip transfers it to the outside, where the second heat sink then emits the heat to the outside air (more information can be found here). I have found it to be very energy efficient. That, with a folding table (found free in good shape) and the hot-plate I already had, completed the kitchen; and this spring I added a canopy to provide some shade and a couple of strings of solar lights for in the evenings.


    This summer has been rather warm, in the trailer, so far. The fans that I had installed in the skylight did not always keep up with the heat. Fortunately I still had another fan that I placed in one of the windows. From my monitoring of my energy usage (I'll spare you the math this time) I'm used about $25 a month in the winter, and $15-20 in the summer. And like most electric bills, most of that it my heating and cooling. With more shade in the summer, I could probably bring that down to $10.
   And now the bad news; in early April I was injured at work (the other reason why you haven't heard from me). My hand was severely cut on all four fingers and my thumb. This effectively cancelled all summer plans. I have about 60% of the use of my hand back now, but a good portion is still numb and my thumb just barely bends. So, I have not gone riding all summer, nor gone kayaking as I had planned. I did do some camping and hiking on memorial day weekend, at natural bridge in Kentucky. This waterfall wasn't out-of-the way, but it was in an area that many people (including my fellow hikers) miss. It was tall enough for me to shower in (I'm 6'2") with the pool underneath, and about ten feet wide and a large sandy beach to stretch out on. Probably one of the nicest spots in the park.


    I've improved my camping equipment, bought a lighter hammock and backpack (with a camelback). With my backpack with the food and change of clothes up in a tree, this was my campsite:


    I was using my rain jacket for shade and to keep the bugs off. The new hammock was very comfortable and was much lighter in my pack than the previous canvas one. I also had taken my tiny soda can alcohol burner, which generated quite a bit of interest when I cooked my entire dinner on it. My camping gear all fits in my pack now, so I've been keeping it in the trunk (for those spontaneous getaways).
    And that makes a nice lead into some of the re-posts.


Thursday, November 1, 2012

Almost done!

I apologize for taking so long to get back to you, but between autumn rain, a crazy work schedule and a mild case of the flu, I didn't get many full days available to work on the trailer. I ended up doing a little bit here and there, jumping from one thing to another; It made it difficult to to 'before and after' pics. But this should get you caught up to date.

I did get the bed frame built, as well as buying a mattress. I decided upon a memory foam mattress and, so far, I've been happy with it. I also covered the frame with canvas to both protect the wood and mattress. Here's the frame as I was building it and as finished:

My original idea for lifting the bed up to the ceiling was insufficient for the weight of both the frame and the mattress, so I'm having to redesign that, but otherwise it's gone well. And yes, those are the tools I used, a hand saw and a hand drill, to do most of the work on the trailer.

For the bookshelves I found a section of the wire shelving that had the supporting rail on the front and back. I tested it and it was able to withstand the weight of the books I'd be putting on it. I thought about several ways of building the supports for the shelves, but in the end I ordered some wire-frame cubes. Steel being stronger, by weight, than wood. You can see in the picture, I used the heavy shelving for the actual shelf, and the cubing frames for the supports (sides and back) and had enough left over for 'caging.'
In my experience I found that the books had to be kept in the shelves; No matter how smooth the road, just hit one pot-hole, and they'll be all over. So for this trailer, I rigged the extra frames so that they can slide in and lock into the front of the shelves in order to contain the books. I can still see where everything is, and it stays there. Of course, when I'm camped, the cages slide out and store out of the way.

I also got the networking all wired in, I'm typing to you from the trailer now. Here's my desk, which is that one exception I was talking about when I was telling you about the lighting. I bought an RGB LED bulb that came with a remote, for the light over the desk. I did decide, after a couple of days, to add another over the bed for a reading light.


And for the Pièce de résistance! A co-worker had a projector that he gave me in exchange for some computer work. I installed it on the shelf at the back of the trailer (the initial reason for the shelf actually) and with the addition of a 5.1 speaker system, I have a home theater!

I'm working on the screen, just a sheet now and it seems to work well. Yes...I know a home theater is not exactly energy saving, but am I not entitled to a little after saving all the rest? Well, we will see how much it costs me after the first month.

The final couple of days, I was moving the RV and both the old and new trailers around, as well as working on the trailer. During this time, poor Freyja had to spend most of the day outside in her kennel. But now that that is all done she and the boys have plenty of room to go outside. I found more of the wire frame cubes at the ReStore and are using them as caging for them to get from the cat-door in the trailer to the litter box. I'm not keeping that inside if I can help it, especially in winter! I have a lot more of the cubes than what you see here, and they will be used for my kitchen. I'm looking at either an Easy-up or some sort of gazebo that will both break down easily and be sturdy for over my kitchen.

That gets you about caught up. I have a few more things to do, and may have to change a few things as I live in it and find what ideas didn't work. I'll keep you posted, thanks for reading!

Thursday, September 27, 2012

Hiking in Tenn and some new lights

It's been a few days, I know, but I had to take some time off an relax a bit before autumn really sets in. I took a trip down to the Smoky Mountains and did some hiking and saw some friends. I finally got around to seeing Gabe Mountain and Hen Wallow Falls; it's one of the shorter hikes but I kept doing the longer hikes in the past as Hen Wallow is a 'there and back' rather than part of a loop. I got up real early to catch the morning light.
Gabe Mountain trail
I spend some time at the falls as I knew it would be some time before anyone else arrived and I would have the place to myself for awhile.
Hen Wallow Falls
When I got home, it was back to work on the trailer, as I had a couple days of my vacation left. I finished the headliner (as you can see in the pics below) and installed a couple of shelves along the ceiling. The lights I had ordered had also arrived; I had found on Amazon a string of LED lights that were 12v and were RGB, meaning I could change their color to anything that suited me. In addition I had picked up some 110v LED lights on clearance after the holidays last year. This gives me all the lighting I need (with one exception) for when I'm plugged in and for when I'm running on solar.

I've gotten the 110v lights installed, both a white and a blue string. I can use both or just each separately as I installed a switched outlet just for them. (blue is shown)
 The 12v LEDs will be installed along the opposite wall as indirect lighting. Here they are when I was testing them right out of the package. They came with an infrared receiver and a 42 button remote. The direct light from the string overwhelmed the camera, but as you can see from the reflected glow I had them set to violet. The remote comes with 24 preset colors, and places for 6 user defined settings, as well as flash, strobe and fade; more than I'll need (or ever use).
I think I'm ready to begin building the bed frame and look into buying a mattress.

Friday, September 14, 2012

A desk and a start on the ceiling

It's been awhile since I've had a good desk that I can work at. Right now I either work in bed or at a "desk" I made in the RV that I sit sideways at. I was actually looking at a new desk (frosted glass with a keyboard drawer at $100) that I was going to treat myself on. Well, the other day I was in the ReStore when I found a desk at a good price, actually a better desk but without a keyboard drawer. But between the price ($30) and that it would fit curve at the front of the trailer better. I wish I had taken a picture of it before I modified it, so you could get a better I idea of what I did.

First of all, it was obviously designed for computers before flat-screens, as there was a glass tier, about 2" above the main glass desk, that sat back behind the two wings and was large enough for a CRT monitor. Above that (and again behind the two side wings) was a third glass shelf, at the same level as the speaker shelves. The two wings were at an angle very similar to the curve of the front of the trailer (or so I was thinking) and would mount right up if I eliminated the back portion.

And that is what I ended up doing, there were two metal frames, bottom and middle, that I cut the back squares off, just leaving the three angled sections. I then drilled holes in them to mount what was the rear support in the center. I also moved the shelf brackets for the top shelf out onto the edges of the speaker shelves so that I can still use it. Here is the result:

 I did add one more thing after this photo, I added an additional support at the center of the upper glass shelf. I was concerned that the speaker shelves alone wouldn't support much weight upon it.

It is attached to the wall, so it is not going to slide around, with enough room for cables between it and the wall. I was planning to mount the left and right monitors to the (white) rail, but this desk will work out better as I can mount them closer to eye level without taking up desk space. The center monitor still will take desk space, as it will not mount on a wall.

As you can also see, I've finished putting up the side rails and the trim around the window (yea!). I've also added the second layer of insulation in the roof and the system to keep it in place. I started on the headliner as well, but started running out of daylight, so I'll probably finish that over the next couple of days after work.

Until then!

Thursday, September 13, 2012

Need my socks and an air guitar

I apologize for the hiatus, I had some vehicle trouble, but it's taken care of now.
I actually did get quite a bit done: The floor is done, with a few tricks. It looks great!

As well as the wall papering. I did something a little different with the walls (as you can see). You know the old adage that horizontal stripes make you look...well, bigger? I thought I'd try it to make it seem bigger. It does seem to work; I was working on the layout for the (upcoming) bed frame and I had to go back out to the trailer twice to verify the space. I kept thinking it was bigger! So, what did I use to achieve this? Bed sheets. They were about 1/10th the price of wallpaper; it was a little more than paint (after figuring in adhesive) but a much better result in my opinion. I have put most of the side rails back up (repainted them as well), a couple more to go as I have to cut them to fit around the windows.

While doing the floor, I didn't want to lose the use of the tie-downs, as I will be hauling the motorcycle when I'm traveling, so I came up with this:
Now you don't see it...
now you do!








All four tie-downs can be accessed this way, and when covered up they are barely noticeable. I'm currently figuring a way for a "tail-gate" for the floor, to keep debris out when I close the trailer's tail-gate; probably some small hinges and some of the extra floorboards.

More tomorrow!

Thursday, July 5, 2012

More windows

I apologize for no posts for awhile, the heat recently has been unbearable. I had picked up a thermometer with a remote sensor for later installation in the trailer. For now I have the remote under the awning of the RV, when I got home one afternoon, this is what I saw:

Yes! That is a high of 111 degrees. But I got back to working on the trailer today, several hours in fact. Worked some more on the wiring, more 12v and some data cables, and I installed another window, his first of two.

I had been contemplating what to do about additional windows, ones that opened that is. I had pretty much decided upon ordering some windows from the home store, expensive, but they would be the exact size I needed. While searching for some other parts I needed for another project I found a van with the same windows as mine, and I began thinking. That would be cool! The trailer would match the van, and the windows are already designed for a mobile installation. Talking to the owner I was able to pick up two windows for $25 apiece, much less expensive than ordering a similarly sized window would have been.

 Next involved cutting (yet another) hole in the trailer. After making a cardboard template, I laid out the location for the window and began cutting.

A couple of problems I anticipated when I began this: First, the windows are curved, to match the curve of the side of the van whereas the trailer wall is flat. This meant that the top and bottom of the window would be flat against the wall, the center would curve away, leaving a gap of about an inch. I've spent the past week trying out various solutions, even using pieces of vinyl siding to fill the gap. In the end, the second issue ending up being the solution to the first!

In the van, the wall is steel and thin, whereas the trailer's skin is aluminum and with the insulation and inside paneling is a little over a inch thick. The manufacturer used an aluminum rail around the inside of the window, screwed to the window frame to hold it in place, the steel supporting the weight of the window. The aluminum of the trailer alone would not support the weight, but the metal, insulation and paneling would, so I thought. What I did in the end, was to use sections of the mounting rail from the window to hold the upper and lower side of the window (you can see two in the picture above), only cutting the foam board insulation just enough so that it all was wedged in place at the end. at the sides of the window, I mounted it just far enough from the internal wall supports, so that when the rail pieces were installed, the metal wall would flex outward some, reducing the gap from the wall to the window frame. By doing this, the gap was reduced, at the center, to about 3/8". This was a distance easily filled by the bead of windshield caulking that I was using to waterproof it anyway! The remaining space under the edge of the window frame I filled with white window caulking, to improve aerodynamics mostly, but also for aesthetics and weatherproofing.

And I finished it just in time! As I was doing the last of the caulking a thunderstorm started rolling in. I had just enough time to put all the tools away and clean up the trash when it started raining. It was quite a good sized storm, a couple of (very!) close hits startled both the cats and I. But after it passed I checked the window, not a single leak, not even damp!

And as you can see in the picture, I even was able to use the blind from the original window. Tomorrow I'll be doing the other side.


Sunday, June 17, 2012

A new window and door

I started cutting holes in the trailer.

As you remember, I picked up an accent window at the re-store about a week ago, I got it installed yesterday. I'm still working on the inside frame as it was designed for a thicker wall than that of the trailer, but as you can see below it lets in a lot of light.

I also installed a cat door. While I was living in the old trailer I designed a set-up for a cage and litter box outside for Amaratzu. I didn't use a cat door, but instead used some plexiglass to frame an opening in one of the windows. In winter I devised a cat-flap to help hold heat, but it was still occasionally a problem. This time I decided to install an actual cat door to help retain heat, and for a better appearance. This door also locks, for security on the road. I still need to devise a couple of hooks to hang the cage from, but I think I can reuse the ones from the old trailer.


Saturday, June 16, 2012

Insulation

 Well, it took me a few days, but the insulation is 90% finished. As you saw, I removed all of the interior panels to have access to all of the walls.Once I had all the measurements I could pick up the insulation that I needed. The walls are 1" thick so I was thinking two layers of 1/2" foam board ,strangely enough, two layers of 1/2" gave more R value than a single 1" layer". It was a good thing that I did, as a single layer of 1" board would not have worked in the end, nor would have two 1/2" layers.

After cutting and installing the sections of foam board I discovered that I would not be able to get a second layer in. The upright supports are a Z-channel so I was fitting the boards behind one support and up against the next, pressing the foam unto the exposed screws. The remaining space was only 3/8", not enough for another piece of foam.

So I taped up what I had and did some thinking. Again at the Re-Store seeking ideas I found they had rolls of carpet padding. Now the padding's R value is negligible, but it would fill the space and do some good.

Here's a shot of the foam board all installed. Doing the roof and the corners, as they are  rounded, took some creativity. The doubly curved section at the front of the trailer's roof looks like a jigsaw puzzle, but I filled every nook and cranny. I used metal foil table to tape all the seams and the uprights. I prefer metal foil over duct tape and it: stays where I put it, sticks to everything, and it's SHINY.

Sorry, no pics of installing the padding, It was frustrating enough without pausing for a pic. I had to attach one end of the interior paneling and slide a section of padding that I had pre-cut behind the panel.

Here it is with the panels all re- installed. You can see a bit of the padding at the corners where I've left those pieces off. I left those off so I can work on the wiring. The 110v wiring is run inside the frame as I described earlier, the 12v wiring I ran behind the foam board as I installed that.

I believe I've already noticed a difference with the insulation. The trailer is parked in the sun for the moment and it gets quite warm inside. Since putting up the roof insulation it has seemed a little cooler.

Monday, June 11, 2012

Solar panels and 12v wiring

Since I talked about the 110 wiring yesterday, I thought that today I would cover the 12v wiring.

I am a firm believer in renewable energy, and since solar is more portable than wind, hydroelectric or geothermal (if anyone's got a portable geyser I'll buy it off you!) that is the route I've taken. As most electronics use 12v and/or 5v for the actual circuitry, it is easy to convert them to use the 12v directly. I give an example of this below.

(BTW, that would be Domino wondering what I'm doing)
The solar panels, charge controller and battery bank is the usual setup, in fact what I have started with is a kit (minus the batteries) available from Amazon. The batteries I am using are deep cycle RV batteries, as my power requirements and not high, I've found three to be enough. I have also added a link to connect to the charging system of the van. This keeps the battery bank charged when I'm on the road and also can charge the van's battery from the panels.

I haven't decided on the form of the 12v outlets I will be using, I would like to stay away from using 'cigarette lighter' plugs. I would like something like a dual banana plug, but that is polarized so it cannot be plugged in backwards. Any suggestions?

At a festival recently I took the panels and one battery with me to demonstrate the computer I have put together. The flat panel display had a 20v power supply, but when I opened the case I found a voltage regulator took that to 12v immediately, bypassing that gave me a 12v powered screen.

The computer is a thin client. It is a small 12v powered and does not have an internal hard drive. It is designed to boot over a network or from USB. For demonstration purposes I run a modified Puppy Linux from a 1GB USB, but for everyday I have a 500GB USB HD running Ubuntu. Fully charged, a single battery can run the computer, screen and 1GB stick four about 5 hours.

Sunday, June 10, 2012

Wiring, and a bonus!

I had a couple of great finds yesterday. I discovered that the wiring for the tail lights is inside the frame, and that the opening for it was large enough to run the 110 wiring in. So, with the help of a little grease, I threaded wire through the frame. This gave me two runs from front to back without having to drill any holes, and they are safely protected inside the steel tubing. In the end, there will be five outlets, one at each corner, inside, one outside where the power will be connected, and one additional switched outlet that will be mounted near the ceiling.
I have a store near me, called The Re-store, run by Habitat for Humanity, they accept donations of all sorts, but mainly salvage from construction and demolition of homes and offices. I have found a lot of what I have needed there, including all of the 110v wire I have needed (including the armored) and the outlets. I used two GCFI outlets to give me two 'circuits' as I did not want to install a breaker box.

At the Re-store I also found this! A light from a door frame for only $35. When I saw it I was thinking of installing it in the door, but I think it will weaken it too much. So instead I'm going to mount it in the wall next to the door; this will give me a floor to ceiling window. This is going to be epic!


Saturday, June 9, 2012

Tearing it down

In preparation for the wiring and insulation I've removed all of the interior and cleaned it all up. I needed to know what exactly I was dealing this to properly plan everything.

All the interior panels all labeled and (kinda) neatly stacked.