I started cutting holes in the trailer.
As you remember, I picked up an accent window at the re-store about a week ago, I got it installed yesterday. I'm still working on the inside frame as it was designed for a thicker wall than that of the trailer, but as you can see below it lets in a lot of light.
I also installed a cat door. While I was living in the old trailer I designed a set-up for a cage and litter box outside for Amaratzu. I didn't use a cat door, but instead used some plexiglass to frame an opening in one of the windows. In winter I devised a cat-flap to help hold heat, but it was still occasionally a problem. This time I decided to install an actual cat door to help retain heat, and for a better appearance. This door also locks, for security on the road. I still need to devise a couple of hooks to hang the cage from, but I think I can reuse the ones from the old trailer.
Sunday, June 17, 2012
Saturday, June 16, 2012
Insulation
Well, it took me a few days, but the insulation is 90% finished. As you saw, I removed all of the interior panels to have access to all of the walls.Once I had all the measurements I could pick up the insulation that I needed. The walls are 1" thick so I was thinking two layers of 1/2" foam board ,strangely enough, two layers of 1/2" gave more R value than a single 1" layer". It was a good thing that I did, as a single layer of 1" board would not have worked in the end, nor would have two 1/2" layers.
After cutting and installing the sections of foam board I discovered that I would not be able to get a second layer in. The upright supports are a Z-channel so I was fitting the boards behind one support and up against the next, pressing the foam unto the exposed screws. The remaining space was only 3/8", not enough for another piece of foam.
So I taped up what I had and did some thinking. Again at the Re-Store seeking ideas I found they had rolls of carpet padding. Now the padding's R value is negligible, but it would fill the space and do some good.
Here's a shot of the foam board all installed. Doing the roof and the corners, as they are rounded, took some creativity. The doubly curved section at the front of the trailer's roof looks like a jigsaw puzzle, but I filled every nook and cranny. I used metal foil table to tape all the seams and the uprights. I prefer metal foil over duct tape and it: stays where I put it, sticks to everything, and it's SHINY.
Sorry, no pics of installing the padding, It was frustrating enough without pausing for a pic. I had to attach one end of the interior paneling and slide a section of padding that I had pre-cut behind the panel.
Here it is with the panels all re- installed. You can see a bit of the padding at the corners where I've left those pieces off. I left those off so I can work on the wiring. The 110v wiring is run inside the frame as I described earlier, the 12v wiring I ran behind the foam board as I installed that.
I believe I've already noticed a difference with the insulation. The trailer is parked in the sun for the moment and it gets quite warm inside. Since putting up the roof insulation it has seemed a little cooler.
After cutting and installing the sections of foam board I discovered that I would not be able to get a second layer in. The upright supports are a Z-channel so I was fitting the boards behind one support and up against the next, pressing the foam unto the exposed screws. The remaining space was only 3/8", not enough for another piece of foam.
So I taped up what I had and did some thinking. Again at the Re-Store seeking ideas I found they had rolls of carpet padding. Now the padding's R value is negligible, but it would fill the space and do some good.
Here's a shot of the foam board all installed. Doing the roof and the corners, as they are rounded, took some creativity. The doubly curved section at the front of the trailer's roof looks like a jigsaw puzzle, but I filled every nook and cranny. I used metal foil table to tape all the seams and the uprights. I prefer metal foil over duct tape and it: stays where I put it, sticks to everything, and it's SHINY.
Sorry, no pics of installing the padding, It was frustrating enough without pausing for a pic. I had to attach one end of the interior paneling and slide a section of padding that I had pre-cut behind the panel.
Here it is with the panels all re- installed. You can see a bit of the padding at the corners where I've left those pieces off. I left those off so I can work on the wiring. The 110v wiring is run inside the frame as I described earlier, the 12v wiring I ran behind the foam board as I installed that.
I believe I've already noticed a difference with the insulation. The trailer is parked in the sun for the moment and it gets quite warm inside. Since putting up the roof insulation it has seemed a little cooler.
Monday, June 11, 2012
Solar panels and 12v wiring
Since I talked about the 110 wiring yesterday, I thought that today I would cover the 12v wiring.
I am a firm believer in renewable energy, and since solar is more portable than wind, hydroelectric or geothermal (if anyone's got a portable geyser I'll buy it off you!) that is the route I've taken. As most electronics use 12v and/or 5v for the actual circuitry, it is easy to convert them to use the 12v directly. I give an example of this below.
(BTW, that would be Domino wondering what I'm doing)
The solar panels, charge controller and battery bank is the usual setup, in fact what I have started with is a kit (minus the batteries) available from Amazon. The batteries I am using are deep cycle RV batteries, as my power requirements and not high, I've found three to be enough. I have also added a link to connect to the charging system of the van. This keeps the battery bank charged when I'm on the road and also can charge the van's battery from the panels.
I haven't decided on the form of the 12v outlets I will be using, I would like to stay away from using 'cigarette lighter' plugs. I would like something like a dual banana plug, but that is polarized so it cannot be plugged in backwards. Any suggestions?
At a festival recently I took the panels and one battery with me to demonstrate the computer I have put together. The flat panel display had a 20v power supply, but when I opened the case I found a voltage regulator took that to 12v immediately, bypassing that gave me a 12v powered screen.
The computer is a thin client. It is a small 12v powered and does not have an internal hard drive. It is designed to boot over a network or from USB. For demonstration purposes I run a modified Puppy Linux from a 1GB USB, but for everyday I have a 500GB USB HD running Ubuntu. Fully charged, a single battery can run the computer, screen and 1GB stick four about 5 hours.
(BTW, that would be Domino wondering what I'm doing)
The solar panels, charge controller and battery bank is the usual setup, in fact what I have started with is a kit (minus the batteries) available from Amazon. The batteries I am using are deep cycle RV batteries, as my power requirements and not high, I've found three to be enough. I have also added a link to connect to the charging system of the van. This keeps the battery bank charged when I'm on the road and also can charge the van's battery from the panels.
At a festival recently I took the panels and one battery with me to demonstrate the computer I have put together. The flat panel display had a 20v power supply, but when I opened the case I found a voltage regulator took that to 12v immediately, bypassing that gave me a 12v powered screen.
The computer is a thin client. It is a small 12v powered and does not have an internal hard drive. It is designed to boot over a network or from USB. For demonstration purposes I run a modified Puppy Linux from a 1GB USB, but for everyday I have a 500GB USB HD running Ubuntu. Fully charged, a single battery can run the computer, screen and 1GB stick four about 5 hours.
Sunday, June 10, 2012
Wiring, and a bonus!
I had a couple of great finds yesterday. I discovered that the wiring for the tail lights is inside the frame, and that the opening for it was large enough to run the 110 wiring in. So, with the help of a little grease, I threaded wire through the frame. This gave me two runs from front to back without having to drill any holes, and they are safely protected inside the steel tubing. In the end, there will be five outlets, one at each corner, inside, one outside where the power will be connected, and one additional switched outlet that will be mounted near the ceiling.
I have a store near me, called The Re-store, run by Habitat for Humanity, they accept donations of all sorts, but mainly salvage from construction and demolition of homes and offices. I have found a lot of what I have needed there, including all of the 110v wire I have needed (including the armored) and the outlets. I used two GCFI outlets to give me two 'circuits' as I did not want to install a breaker box.
At the Re-store I also found this! A light from a door frame for only $35. When I saw it I was thinking of installing it in the door, but I think it will weaken it too much. So instead I'm going to mount it in the wall next to the door; this will give me a floor to ceiling window. This is going to be epic!
I have a store near me, called The Re-store, run by Habitat for Humanity, they accept donations of all sorts, but mainly salvage from construction and demolition of homes and offices. I have found a lot of what I have needed there, including all of the 110v wire I have needed (including the armored) and the outlets. I used two GCFI outlets to give me two 'circuits' as I did not want to install a breaker box.
At the Re-store I also found this! A light from a door frame for only $35. When I saw it I was thinking of installing it in the door, but I think it will weaken it too much. So instead I'm going to mount it in the wall next to the door; this will give me a floor to ceiling window. This is going to be epic!
Saturday, June 9, 2012
Tearing it down
All the interior panels all labeled and (kinda) neatly stacked.
Friday, June 8, 2012
New trailer ... Home actually!
I bought a new trailer the other day. this is going to be my new home. It's a little larger than the last trailer, I can actually stand up in this one. It's 6'x12' and the back is a ramp door. This one even came with a spare tire, which was problem with the previous trailer.
I'm planning out the wiring and the insulation and will be updating on that installation soon.
I'm planning out the wiring and the insulation and will be updating on that installation soon.
Wednesday, June 6, 2012
Returning
Well, I've been debating it for a few months now, since Facebook's introduction of the timeline, and I've decided to move the blog back here. The timeline makes it difficult to post the type of longer entries that I do (as well as infrequent!) and is more for short comments and pictures. So you are going to see a burst of entries as I move everything for the past couple of years over here, and then get you updated on the current projects.
Subscribe to:
Posts (Atom)












